BeagleBoard-xM is based on the TI DM and delivers increased performance . The schematic and PCB remain the same as revision C1. BeagleBoard-xM LCD7. System Reference Manual. Revision B. Page 2 of THIS DOCUMENT. This work is licensed under the Creative. BeagleBoard-xM Rev C System Reference Manual Revision April 4, Page 1 of REF: BB_SRM_xM. BeagleBoard-xM System Reference Manual.

Author: Voodoonris Gazilkree
Country: Bhutan
Language: English (Spanish)
Genre: Art
Published (Last): 20 January 2017
Pages: 41
PDF File Size: 3.39 Mb
ePub File Size: 4.75 Mb
ISBN: 842-1-39683-825-7
Downloads: 1523
Price: Free* [*Free Regsitration Required]
Uploader: Nikoshicage

Figure 27 is the sequence in which the power rails, clocks, and reset signal come up. Figure 42 is the microSD interface design on the BeagleBoard.

Reference Manual The expansion header is provided to allow a limited number of functions to be added to the BeagleBoard sfhematics the addition of a daughtercard. Revision C2 Reference Manual 4. This cable is not supplied with BeagleBoard but can be obtained through numerous sources. Page 41 – Figure They require a 4GB SD card for the image to fit.

BeagleBoard XM C2 Reference Manual

Send all comments and errors concerning this SRM to the author at. Decompress the verification image file using 7-zip. Figure 11 shows the proper connection point for the cable. Figure 51 is the design of the expansion connector and the interfaces to the processor. The schematic and Shcematics remain the same as revision C1. Figure 50 shows the interconnection to the processor. With a slightly enlarged footprint of 3. Main Expansion Header Processor Connections Reference Manual Beagpeboard expansion header is provided to allow a limited number of functions to be added to the BeagleBoard via the addition of a daughtercard.


Beagleboard Accessories This section covers these accessories and add-ons and provides information on where they may be obtained.

Power Connector The supply must be at least 1A with a maximum of 3A. How these connectors are used is determined by the design of the adapter board that is connected to them.


This connector is populated on the board. All boards will be returned via standard mail if an issue is found. Follow the instructions found there, but use the images located beaglebaord this site.

Processor Pin Muxing Settings The power supply is not provided with the BeagleBoard, but can be obtained from various sources. Beagleboard Expansion Card Design Information This section provides information on what is required from a mechanical and electrical aspect to create expansion cards for the BeagleBoard that are designed to connect to the Expansion header on the BeagleBoard.

Power Connector Page – Figure Page 45 – Figure There is also an option to ground the ID on the board and is discussed later in this document. Linux is a registered trademark of Linus Torvalds. If desired, the resistors can be installed to pull the signals high. TPS and what remains from the current consumed by the BeagleBoard and is intended to be used to provide a rail for voltage level conversion only.

This makes the 3. Got it, continue to print.

To view the PCB files, a free viewer can be downloaded from Cadence. Please check on BeagleBoard. This section covers these accessories and add-ons and provides information on where they may be obtained. These versions are 2. The camera module is not supplied with the BeagleBoard. IN The charge pump input voltage.



Table 4 is a list of all of the signals used on the processor for the BeagleBoard and the required mode setting for each pin. DM37x Block Diagram Page 65 of Page 39 – Figure Beagleboard-xm System Revision C2 Table Reset Circuitry Page 65 – Figure The client port is limited in most cases to mA by the PC. It is recommended that you use 7-zip when unzipping these files. Page – Table However, it is not expected that any of the resistors will need to be installed.

All signals from the BeagleBoard are at 1. BeagleBoard Expansion Board E These are the loading options to enable the new mode used by the —xM or the legacy mode used by the BeagleBoard. The JTAG emulator must support 1.

Revision C2 Reference Manual BeagleBoard Specification This section covers the specifications of the BeagleBoard and provides a high level description of the major components and schemattics that make up the BeagleBoard. Remove the USB cable and re insert. Processor Audio Signals Page 88 – Figure Vbat Power Conditioning R14 and R15, the actual voltage can be adjusted if needed.