CONFIGURATION ROUTAGE OSPF PDF

This document uses these configurations. ip unnumbered Ethernet2/0/0 router ospf 1 network area 0. Redistribution Configuration Syntax and Examples. IGRP and EIGRP. OSPF. RIP. Redistributing Static Routes Except Gateway of Last resort in. This article describes some basic OSPF configuration.

Author: Doujora Sagor
Country: Anguilla
Language: English (Spanish)
Genre: Science
Published (Last): 17 July 2012
Pages: 264
PDF File Size: 19.57 Mb
ePub File Size: 17.30 Mb
ISBN: 514-7-87929-147-5
Downloads: 32781
Price: Free* [*Free Regsitration Required]
Uploader: Dajin

If the output does not display the intended configuration, repeat the instructions in this example to correct the configuration. As you can see from the network topology depicted above, routers R1 and R3 are in the area 0 and area 1, respectively.

OSPF configuration

Because R1 connects only to R2, we only need to establish a neighbor relationship with R2 and advertise directly connected subnet into OSPF. Area IDs are unique numeric identifiers, in dotted decimal notation. NOTE We have used the router-id 1.

Home About Contact Support our work. To verify if the routing updated were exchanged, we can use the show ip route command.

To quickly configure a single-area OSPF network, copy the following commands, paste them into a text file, remove any line breaks, change any details necessary to match your network configuration, copy and paste the commands into the Configuratjon at the [edit] hierarchy level, and then enter commit from configuration mode.

  HEPATOPATIAS PERROS PDF

To confirm your OSPFv3 configuration, enter the show protocols ospf3 command.

Area IDs need only be unique within an AS. This can be done by using the following sequence of commands on both routers:.

Example: Configuring a Single-Area OSPF Network

Characters IA in front of the routes indicate that these routes reside in different areas. Confirm your configuration by entering the show protocols ospf command. R3 is in the area 1. For a single-area OSPFv3 network, include the ospf3 statement at the [edit protocols] hierarchy level.

Our goal is to advertise the subnets directly connected to R1 and R3. To verify if directly connected subnets are really rougage into the different area, we can use the show ip route ospf command on both R1 and R We can do that using the following sequence of commands:.

The network commands entered on both routers include confiburation directly ocnfiguration to both routers. Then we need to define what network will be advertised into OSPF. Configure the device interfaces. We will use the following network topology:. Now R2 should have neighbor relationship with both R1 and R3. You must also create a backbone area if your network consists of multiple areas.

To do that, the following configuration on R1 will be used:. All other networks or areas in the AS must be directly connected to the backbone area by area border routers that have interfaces in more than one area. For example, here is the output of the command on R To do that, we need to rourage different area ID for each neighbor relationship, 0 for R1 and 1 for R2.

  ANALISIS Y DISEO DE SISTEMAS DE INFORMACION JEFFREY WHITTEN PDF

OSPF configuration

OSPF basic configuration is very simple. We can verify that the routers have become neighbors by typing the show ip ospf neighbors command on either router:. In an autonomous system ASthe backbone area is always assigned area ID 0.

Confirm that the Area field displays the value that you configured. Next, you need to define oospf which interfaces OSPF will run and what networks will be advertised.

Configure the router identifiers for the devices in your OSPF network. Configuration of R3 looks similar, but with one difference, namely area number. We can verify that by using the show ip ospf neighbor command:. Jan 26, upravnik. Orutage this example we have two OSPF areas — area 0 and area 1.