Marine manuals and free pdf instructions. Find the marine product manual you need at ManualsOnline. Furuno Ls Fish Finder User Manual. Page 1. Ls – read user manual online or download in PDF format. Pages in total: en este manual. Asi mismo, FURUNO apreciaría cualquier suge- rencia o comentario en relación con el equipo. Características. La FURUNO LS es una.

Author: Arashitaur Zulkigal
Country: Sweden
Language: English (Spanish)
Genre: Career
Published (Last): 22 September 2005
Pages: 408
PDF File Size: 2.95 Mb
ePub File Size: 13.54 Mb
ISBN: 890-6-87583-973-3
Downloads: 45291
Price: Free* [*Free Regsitration Required]
Uploader: Grorr

Carefully remove anymarine life with a piece of wood orfine-grade sandpaper. For any NG,request service. Do not position the sensor farther into the water than necessary to avoid increasing drag, spray, and water noise and reducing boat speed.

Furuno LS-4100 Fishfinder

No user-serviceable parts inside. Only qualified personnel should workinside the equipment. In the dual frequency display, theA-scope display is only available withthe high frequency display. If you cannot restorenormal operation, contact your dealerfor advice. Lower HalfSaw along slopeof hull. Don’t have an account? Page 25 Requires appropriate nav data. Iec Data Sentences 4. Choose the water type with which to use the LS, from Salt or Fresh. Outputs the data sentences of LS only.


By pressing ‘print’ button you will print only current page. To reset the odometer to zero,clear the memory. Page 4 The installer of the equipment is solely responsible for the proper installation of the equipment.

Position the second cable clamp halfway between the first clamp and the cable hole. Construction of fairing block 3.

Fire, electrical shock or serious injurycan result. Shifting the range The basic range may be shifted up or down in the manual mode as follows: Minimize surfacecracking by chamfering the gelcoat. Page 36 Transom hole: For planing hulls, a practical location is generally rather far astern, so that the transducer is always in water regardless of the planing attitude. Repeat step 1 to ensure that theangle of the sensor is correct. Do not position the sensorfarther into the water than necessaryto avoid increasing drag, spray, andwater noise and reducing boatspeed.

Use the proper gain setting. Nothing appears if no connector is connected. Fill the gap between the wedge front of the transducer and transom with epoxy material to eliminate any air spaces.

Furuno Fish Finder Ls User Guide |

Thismode is useful for determining bottomcontour. Beeps are generated while the tripdistance is being reset. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition.

If excessivenoise shows on the screen, the groundmay be inadequate. Establishing the groundLocknutThe ground wire 1. A special connector is required to test the NMEA mznual. Apply a sufficient amount of high quality caulking compound to the top surface of the transducer, around the threads of the stuffing tube and inside the mounting hole and fairing Press the [MARK] key again. Data is output at two-second intervals. The signal line ground is isolated fromthe chassis ground, however the powerline is not insulated.


Check the transducer facefor cleanliness each time furunl boat isdry-docked. Don’t show me this message again.

If a hole has been drilled in thetransom, open the appropriate slot inthe transom cable cover. Adjusting fufuno gainftftftftft60ft30ft15ftThe [GAIN] key adjusts the sensitivity ofthe receiver. Page 3 A warning label is attached to the equipment.

Furuno Ls : SONAR User Manual

Page of 48 Go. The nav data displays appear on mahual leftof the screen. Dual Frequency Display Single frequency display 50 kHz The sounder uses ultrasonic signals to detect bottom conditions.