5. Newsletter. Before doing anything else, make sure to sign up for the free Energy .. Bedini Mono-Pole Energizer circuit that is extremely similar to the diagram. WHAT IS THE BEDINI SG? Get a copy of the Bedini SG – The Authorized Beginner’s Manual if you want to learn all about the Bedini SG and how to build your. This is a hands-on explanation of how to build a monopole energizer based on John C. Bedini’s patent No. 6,, This system charges lead acid or gel cell.

Author: Vudoktilar Kejar
Country: Reunion
Language: English (Spanish)
Genre: Music
Published (Last): 15 February 2006
Pages: 271
PDF File Size: 2.91 Mb
ePub File Size: 20.69 Mb
ISBN: 657-8-44508-887-6
Downloads: 46366
Price: Free* [*Free Regsitration Required]
Uploader: Nigor

You might find that the recovery pulse would widen out and mzke become larger than the drive pulse at least up to saturation of coil. Wait a few minutes for the battery voltage to stabilize again. You may also use a mains powered 12VDC mnoopole supply in place of a battery. Wait until the rotor speed stabilizes, about 1 minute You may see the ammeter fluctuate while the rotor is coming up to speed.

Slowly adjust the potentiometer, a little bit at a time, until you get the highest RPM for the minimum current drawn from the primary battery. John Bedini has spent over 30 years developing this technology and has several U. This forum is for educational purposes only. Before starting the charge and discharge cycles for the COP testing it is a good idea to figure out what your testing schedule monoopole be. Look at the picture on the schematic for details.

Bedini SSG Monopole Energizer Motor Kit

Here are the steps you need to mmake To link the article above use: Find all posts by darkwizard. Originally Posted by dambit. I will say that the capacitor version is interesting and it does have at least one advantage over the SSG version: Quantity – One length of each wire, about ” 30mm Magnets Purpose – To attach to the outside of the rotor, in order to maintain rotation and provide an induced voltage on the trigger maje to fire the transistor.


The most striking example is the pendulum; during the filming of that segment the pendulum looked very promising but in the end turned out to be not so great, at least from a battery charging standpoint.

Don I think you s put something in place of a blank page. Watching the videos of Bedini, he uses up to 10 AMP on the large machine, and much less for the smaller machines. As such, the learning process starts when one refrains from assuming a conventional energy transfer from the primary source batterydriving the motor, thereby pushing electron current into the charging bank. Nature does not care what the coil looks like. Measure the current and write it down as the “Load Amps in the Output Joules section of the table.

I have been doing bednii Bedini will do, thinkering with it, it is the right track, build it, love it and thinkering with it, because it is a living thingvacuum energy is doing his job.

I have upgraded my circuit with hall sensors but it is on my head, my software is limited and doesn’t have a hall sensor in order to do the schematic! Connect the charging battery to the Monopole SSG and then connect the primary source battery or power supply.

John Bedini Monopole Generators

Connect the analogue DC panel ammeter in series with the negative terminal of the primary source battery. This requires time to cycle at least one battery through a charging and loading scheme many times to learn how it responds. The maximum discharge load value is calculated by If bedinj potentiometer gets hot back off a little or it will burn out.

Thanks Seph for opening this up. I’ve ruminated long and hard over the ‘SSG is more advanced than the capacitor version’ quote myself and having built a variety of Bedini machines, I’m not convinced. Unrelated photos enregizer be deleted by the moderators. Typical values for a flooded cell battery at 80 degrees F Turn off the Monopole SSG, by disconnecting ro primary battery.


Bedini’s Monopole Energizer – Energetic Forum

Save those old junk car starter batteries for later. Next, figure out how much time you have to collect data. There is a learning maoe here for those who built this motor the way I said to do it about enerhizer people. The table will also calculate the COP of the charging battery. Write down the “Input Amps ” and “Input Watts figures that you obtained from the ” Measuring the “conventional” current into the charging battery” process.

Measure the voltage of the charging battery and note the amps reading on the analog amp meter. However, repeated charge and discharge cycles should improve the COP figure. When you do this, the semiconductor over heats, monopile the current to the transistor stays on and the mechanical oscillator runs slow.

You know already that the conventional charger with repeated load tests will result in less and less load time until the battery has no more capacity to be charged and power a monopoel. For this research to progress, members are asked to commit to one simple directive: Connect the batteries and verify the Monopole SSG runs.

Most batteries, even when new start sulphating straight away as soon as they leave the factory. These books are all available by ordering on-line from Tom Bearden’s or Rick Friedrich’s web-site.