MAGNETEK GPD 515 PDF

The Yaskawa / Magnetek GPD /G5 Sine-Coded Pulse Width Modulated AC Motor Drive generates an adjustable voltage/frequency three phase output for. TTThhhooommmpppsssooonnn CCCooo RRReeellleeeaaassseeeddd /// /// 2. Magnetek GPD AC Drive Start Up and Adjustment Guide. Magnetek G5 GPD | Drives | NEW IN STOCK | CALL or Click for Quote.

Author: Vuzshura Dajora
Country: Suriname
Language: English (Spanish)
Genre: Politics
Published (Last): 10 July 2007
Pages: 36
PDF File Size: 20.45 Mb
ePub File Size: 20.21 Mb
ISBN: 792-7-24788-830-4
Downloads: 91124
Price: Free* [*Free Regsitration Required]
Uploader: Gojar

As the load increases, the speed droops according to the percentage set in b 7 – 0 1. Use a voltmeter to verify that voltage is disconnected from incoming power terminals.

The analog voltage present on terminal 14 will determine torque compensation value. P7 Drive Programming Manual Model: I have now used MROelectric several time and have found them to have the best price and magnettek of several third party vendors I have dealt with.

This feature can be selected to operate over a wide range of conditions. MRO Electric provided excellent service to us mavnetek we needed it most. Equipment uses semi-conductors and is vulnerable to high voltage.

IMPORTANT. Engineering Bulletin # Magnetek GPD Start Up and Adjustment Guide – PDF

VFD Lesson 3. When enabled data ” 1 “the reference loss detection compares the change in reference with respect to time.

Attach the Remote Mount Resistor Unit, maintaining a minimum 1. Display Scaling Factory setting: Fast and efficient service! Easy to configure – The. Two are analog inputs, nine are stored in memory, and one can be from an option card, either analog or digital.

  ECOLOGIA CULTURAL JULIAN STEWARD PDF

Yaskawa / MagneTek / Saftronics / Omron Magnetek G5 GPD 515 Drives

Off-delay Timer Factory setting: With this valuable service, your defective drive will be repaired on a rush magnetke to get it working like new again and back to you fast to help minimize your expensive downtime. Digital Operator Table A Related to Control Method Carrier Frequency Upper Limit C 6 – 0 2: I was please with the service and shipping time. Magnwtek found your company on line ,the sinumeric PCU50 was an obsolete part from the machine manufacturer so we where dead in the waterafter speaking to Joe magnteek was very helpful and knowledgeable, he knew what we needed and the part was in stock newbut he also 51 me some more economic options to choose fromi opted for the new unit and they shipped it the same day.

Multi-Function Analog Input Term. No additional import charges at delivery! This deceleration rate may be longer than the set value C See Note 4 REF. Reinstall and secure Remote Mount Resistor Unit cover and drive front cover.

GPD /G5 Drive Technical Manual |

When a changeable data value is being displayed, pressing this key moves the blinking i. See Table A Range: Contents Contents Introduction Safety Please enter 5 or 9 numbers for the ZIP Code. A Overload Protection Selection Elapsed time is accumulated according to the setting of o 2 – 0 8.

  CANON EOS 1000FN MANUAL PDF

If the fault can now be reset, the cause is most likely the motor or wiring to the motor. Sets the incoming AC voltage to the drive.

Yaskawa / Magnetek GPD 515/G5 Sine-Coded Pulse Width Modulated AC Motor Drive

It should be the manual gpc type to prevent automatic restart following a motor fault and subsequent contact reclosure after cool down. To see Example 1 gpv 2 in detail, refer to Tablesand Refer to manual 1: Droop Control Delay Time Factory setting: Motor accelerates, at the rate corresponding to the preset accel time, to the preset speed.

A Operator Detection Selection It is recommended that this parameter be enabled at all times. Communication option card failure. The motor ramps down to zero speed, then ramps up in the opposite direction.

This function is separate and should not be confused with parameters b 8 – 0 1 and b 8 – 0 2. A Magneteek Detection Output Signal